--------------------------------------------------------------------------------
PROFIBUS Master
--------------------------------------------------------------------------------

V2.8.0.0 
---------
 - PSDPM-530:  Support of upload request on start by application 
 - PSDPM-531:  distribution folder shall match newest definition 
 - PSDPM-532:  RUN and BUS ON flags can be set, when master license is not available. 
 - PSDPM-422:  BUS OFF on the master side  does not clear master's input data area. 
 - PSDPM-504:  PROFIBUS_MSCS1M_CMD_SET_TIME_CNF is not received 
 - PSDPM-505:  High CPU load stopps responding to host 
 - PSDPM-508:  Update Profibus DL to V2.1.8.0 
 - PSDPM-511:  BusOn not cleared on watchdog error 
 - PSDPM-513:  Watchdog error is not counted when BUS flag is OFF 
 - PSDPM-514:  Transmission type is not set at RCX_GET_DPM_IO_INFO_REQ 
 - PSDPM-517:  Modify bus parameter set with user data failed 
 - PSDPM-519:  Reserved area at common status block is not null. 
 - PSDPM-521:  [netx51] Calculate spare time to give CPU resources to system 
 - PSDPM-526:  Master sends CLEAR data at redundant switch 


V2.7.2.0 
---------
 - PSDPM-530:  Support of upload request on start by application 
 - PSDPM-531:  distribution folder shall match newest definition 
 - PSDPM-532:  RUN and BUS ON flags can be set, when master license is not available. 


V2.7.1.0
--------
 - PSDPM-422:  BUS OFF on the master side  does not clear master's input data area. 
 - PSDPM-504:  PROFIBUS_MSCS1M_CMD_SET_TIME_CNF is not received 
 - PSDPM-505:  High CPU load stopps responding to host 
 - PSDPM-508:  Update Profibus DL to V2.1.8.0 
 - PSDPM-511:  BusOn not cleared on watchdog error 
 - PSDPM-513:  Watchdog error is not counted when BUS flag is OFF 
 - PSDPM-514:  Transmission type is not set at RCX_GET_DPM_IO_INFO_REQ 
 - PSDPM-517:  Modify bus parameter set with user data failed 
 - PSDPM-519:  Reserved area at common status block is not null. 
 - PSDPM-521:  [netx51] Calculate spare time to give CPU resources to system 
 - PSDPM-526:  Master sends CLEAR data at redundant switch 


V2.7.0.0
--------
 - PSDPM-422:  BUS OFF on the master side  does not clear master's input data area. 
 - PSDPM-499:  change versionnumber from v2.6 to V2.7 
 - PSDPM-508:  Update Profibus DL to V2.1.8.0 
 - PSDPM-511:  BusOn not cleared on watchdog error 
 - PSDPM-513:  Watchdog error is not counted when BUS flag is OFF 
 - PSDPM-514:  Transmission type is not set at RCX_GET_DPM_IO_INFO_REQ 
 - PSDPM-517:  Modify bus parameter set with user data failed 
 - PSDPM-519:  Reserved area at common status block is not null. 


V2.6.22.4
---------
 - PSDPM-521:  [netx51] Calculate spare time to give CPU resources to system 


V2.6.22.3
---------
 - PSDPM-512:  Channel Init is aborted by stop timeout 


V2.6.22.2
---------
 - PSDPM-506:  [NX51] TagListEditor could not load NXF 


V2.6.22.1
---------
 - PSDPM-505:  High CPU load stopps responding to host 


V2.6.22.0
---------
 - PSDPM-497:  TLR_E_NETWORK_FAULT not displayed after channel init 


V2.6.20.0
---------
 - PSDPM-489:  netX51 firmware shows wrong USB identifier 
 - PSDPM-490:  unexpected very high netX CPU load 


V2.6.19.1
---------
 - PSDPM-504:  PROFIBUS_MSCS1M_CMD_SET_TIME_CNF is not received 


V2.6.19.0
---------
 - PSDPM-486:  Redundant_Mode_ind is not send if started as primary master 
 - PSDPM-487:  Slave parameter set value bMaxChannelDateLen handled wrong 


V2.6.18.0
---------
 - PSDPM-481:  RCX_SET_HANDSHAKE_CONFIG_REQ does not change the handshake mode 
 - PSDPM-482:  bSyncMode is set without a bSyncSource  
 - PSDPM-485:  Update Profibus DL V2.1.6.0 


V2.6.17.0
---------
 - PSDPM-478:  Clear command is send when Watchdog error occurs on redundant master 


V2.6.16.0
---------
 - PSDPM-473:  update to rcX v2.1.10.0 and v2.0.8.24 
 - PSDPM-474:  Slave is deconfigured by Channel Init and watchdog error even by active redundancy master 


V2.6.15.0
---------
 - PSDPM-471:  PROFIBUS_FSPMM2_CMD_INITIATE_REQ fails after ChannelInit 


V2.6.14.0
---------
 - PSDPM-414:  Implement packet to set handshake mode device/host controlled 
 - PSDPM-454:  in redundant systems firmware might send many unexpected PROFIBUS_APM_CMD_REDUNDANT_MODE_IND to the application 
 - PSDPM-459:  Channel init may fail if executed while bus short circuit 
 - PSDPM-460:  Change mode from CLEAR to STOP fail sometimes fails 
 - PSDPM-462:  [NXO] Module firmware uses wrong base priority for COM interrupt 
 - PSDPM-468:  Redundancy mode: Add indications to inform application on top of the active master about status of passive master 
 - PSDPM-469:  update to ProfibusDL V2.1.5.0 


V2.6.13.0
---------
 - PSDPM-448:  firmware generates high IRQ load in host 
 - PSDPM-449:  Channel init fail when duplicate profibus address is detected 
 - PSDPM-450:  Channel init fail after download invalid configuration 
 - PSDPM-457:  Channel init fails after download of invalid configuration database  
 - PSDPM-458:  Channel init fails when duplicate profibus address is detected 


V2.6.12.0
---------
 - PSDPM-428:  Error during Firmware Download (invalid FileHeader value) 


V2.6.11.0
---------
 - PSDPM-398:  Undefined Manufacturer in firmware file header 
 - PSDPM-438:  Com LED shows no error after bus off/on if no slave is connected previously 
 - PSDPM-440:  sometimes Wrong COM flag state in DPM in case of Bus short circuts 


V2.6.10.0
---------
 - PSDPM-430:  DL-Tasks looses packet if Stop-DLE is executed during LL_REQ 


V2.6.9.0
--------
 - PSDPM-417:  update Profibus netx5 HAL to Version 1.4.3 


V2.6.8.0
--------
 - PSDPM-413:  update Profibus HAL to Version 1.5.1 


V2.6.7.0
--------
 - PSDPM-407:  In case cifX card is configured to "Start by Application" using the SET_MODE command does not work 
 - PSDPM-409:  Fspmm sends 126 Fault Ind packets to APM task in case of PassiveToActive switch. 
 - PSDPM-412:  FSPMM2 indications overwrite registered application queue 


V2.6.6.0
--------
 - PSDPM-405:  Indication from Profibus Master has invalid value at ulDest and ulDestID 


V2.6.5.0
--------
 - PSDPM-397:  No response to FDL related services device is not configured 
 - PSDPM-401:  incorrect packet length for PROFIBUS_FSPMM_CMD_APP_REG_REQ returns wrong error code 
 - PSDPM-403:  sometimes lost packets on DP V1 Class 2 service 


V2.6.4.0
--------
 - PSDPM-382:  PROFIBUS Master sends DPV1 service requests to fast 
 - PSDPM-389:  CiR: Activated slave is not configured 
 - PSDPM-391:  unexepcted packet confirmation size for Description  Positive confirmation of packet command PROFIBUS_FSPMM_CMD_SET_PRM_CMD_CNF 
 - PSDPM-395:  CiR: address table overlap status field if new devices are configured 


V2.6.3.3
--------
 - PSDPM-393:  DP V1 support for redundant master system 
 - PSDPM-394:  UNLOCK set on PrmCmd 
